DIY/Contractor Crack injection kit for leaking foundations and basements
Auto Injector series kit.
Ultra low Viscosity Epoxy for any type of crack less than 1/64
The NextStar Auto Injector series of products allow for low pressure injection between 24 to 40 psi without any specialized manual or pneumatic tools at a low cost but with the same professional results. These kits are perfect for the home owners and professionals alike that only do occasional or one time repairs. Perfect for the DoIt Your Self project. No Digging required all injection is from the inside! This Epoxy is slow curing and super thin to allow penetration of cracks that may not even be visible.The auto injectors allow for constant injection pressure over a 24hr time frame to penetrate the smallest of cracks. No special tools required.
Uses: Ultra fine Cracked basement walls, Ultra fine cracks- pin holes, repair of leaking snap-ties , gravity feed, any cracked concrete item including concrete statues etc
Included components . . .
946 mls (1 Quart) of ULV Epoxy Part A and 473mls (1 Pint) Part B ULV Epoxy
Two 10 oz 300ml jars of fast setting Epoxy Crack Seal Port Adhesive (1 jar Part A, 1 jar Part B)
15 Surface ports with Auto injectors (provides same results as professional injectors)
Six wooden sticks & putty knife
Two pair of nitrile gloves
Complete instructions & MSDS Data
Our 10 ft. concrete crack repair kit allows the D-I-Y homeowner or handyman to use the same materials that we supply professional contractors.
FAQ Auto Injector kits
- What is different about auto injector kits?
- What are the different types of auto injector kits
- When would I use these types of kits?
- Why inject ULV epoxy?
- How long will the foundation repair last?
- How long will a standard crack repair take?
- What are the steps for a repair?
- Does NextStar provide help if I have a problem?
Q What is different about auto injector kits?
A The auto injector kit series of easy to use kits that give professional results. Using NextStar’s unique auto injector allows products to be injected under low pressure into concrete foundations without specialty injection tools and costly equipment.
Q What are the different types of auto injector kits?
A Type 1 is our standard polyurethane and can be used in most leaking foundation
cracks from 1/32 – 3/8 inch wide .Type 2 for leaking cracks from 1/64 to 1/32 inch.
Type 3 (this kit) is our Ultra Low Viscosity Epoxy kit that penetrates the smallest possible concrete cracks that could not be injected with polyurethane even under high pressure.
Q When would I use these types of kits?
A The auto injection kits are perfect for the home owner or contractor who only
occasionally do repairs or single job applications. Especially for the ULV Epoxy kit 3.
These kits supply everything that is needed to complete each type of foundation crack repair problem.If you plan to do ongoing repairs using different products the semi pro or contractor kits would be best.
Q Why inject Ultra Low Viscosity Epoxy?
A This Epoxy is perfect for injecting into foundation cracks that may or not be leaking but too small to inject polyurethane. This Ultra Low Viscosity Epoxy is can flow for up to 12 hrs and when used with auto injectors the low pressure can be applied automatically over extended time without human help. Epoxy provides a structural repair.
Q How long will the foundation repair last?
A These type of repairs typically can last the life of the structure
Q How long will a standard crack repair take?
A 8 ft of foundation cracks should take with ULV Epoxy is 4 hrs or less even for a novice. The epoxy will contine to flow for upto 12 hrs with a cure time of 72 hrs.
Q What are the steps for a repair?
1. Clean the concrete wall with wire brush etc to bare concrete wall.
2. Using the epoxy paste provided install injection ports to the wall.
3. Seal over the remainder of the crack with epoxy paste.
4. The Ultra Low Viscosity Epoxy is mixed in a container and injected starting at the lowest port using the auto injectors.
5. The product will flow from the lowest port to the next port up the wall and at this point install the next auto injector when product reaches the next port. Follow this process until the last port is injected.
Q Does NextStar provide help if I have a problem?
A Yes we provide telephone support via toll free at 1-866-445-3984